Jump to content


Photo

WTB : Brake Master Cylinder st202/4 or 205

master cylinder st202 st204 st205 booster brakes

  • Please log in to reply
7 replies to this topic

#1 silycr

silycr

    OZCelica Junkie

  • Queensland Moderator
  • 1,433 posts
  • Gender:Male
  • STATE:QLD

Posted 07 October 2013 - 09:26 PM

Hey guys,

I'm after a brake master cylinder from an ST202/204. Doesn't really matter about condition as it will be getting rebuilt.

Alternatively, if anyone is wrecking their st205 half cut, i could do with the booster and slave from that...

Thanks

#2 sandwichamwin

sandwichamwin

    Forum Member

  • Members
  • PipPip
  • 159 posts
  • Gender:Male
  • Location:Sydney
  • STATE:NSW

Posted 08 October 2013 - 09:35 AM

i have a 204 master + res which needs new seals.

Edited by sandwichamwin, 08 October 2013 - 09:35 AM.


#3 silycr

silycr

    OZCelica Junkie

  • Queensland Moderator
  • 1,433 posts
  • Gender:Male
  • STATE:QLD

Posted 08 October 2013 - 08:50 PM

Would you happen to have the booster as well?

The way I figure, in for a penny, in for a pound. May as well replace it while im there.

If your cylinder is already out, can you tell me, is it the 15/16 or 1 inch version?

#4 sandwichamwin

sandwichamwin

    Forum Member

  • Members
  • PipPip
  • 159 posts
  • Gender:Male
  • Location:Sydney
  • STATE:NSW

Posted 08 October 2013 - 09:47 PM

no booster. I'll have to measure it tomorrow but it was from a December 98 build 204 if that helps for now.

#5 silycr

silycr

    OZCelica Junkie

  • Queensland Moderator
  • 1,433 posts
  • Gender:Male
  • STATE:QLD

Posted 08 October 2013 - 09:49 PM

No worries. It should have the size embossed on the side in a circle to make it easy.

EDIT: ABS btw?

Edited by silycr, 08 October 2013 - 10:17 PM.


#6 sandwichamwin

sandwichamwin

    Forum Member

  • Members
  • PipPip
  • 159 posts
  • Gender:Male
  • Location:Sydney
  • STATE:NSW

Posted 09 October 2013 - 09:54 AM

nope the car did not have ABS

#7 TRD-021

TRD-021

    Forum Member

  • Members
  • PipPip
  • 623 posts
  • Gender:Male
  • Location:Sydney
  • STATE:NSW

Posted 12 October 2013 - 07:46 AM

I thought the st205 and st185 have 15/16 bore size. I'll confirm this when I get back to Sydney I'm pretty sure I've a the st205 mater cylinder somewhere in the garage..

Edited by TRD-021, 12 October 2013 - 07:49 AM.

GT-Four Group A Rallye, Carlos Sainz Edition # 21 out of 150.
Gen 4 ST215 engine conversion, FMIC, Hatech Elite 1500, Forged CP pistons, ST205 rear calipers, front ST205 yet to install.

#8 sandwichamwin

sandwichamwin

    Forum Member

  • Members
  • PipPip
  • 159 posts
  • Gender:Male
  • Location:Sydney
  • STATE:NSW

Posted 13 October 2013 - 03:25 PM

hey mate sorry for the late reply but I dug it out of the garage today and it's 15/16.





Also tagged with one or more of these keywords: master cylinder, st202, st204, st205, booster, brakes

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users